General Care
We recommend that you vacuum your rug regularly to keep it clean and to help prevent the pile of the rug from flattening. If you have purchased a wool rug or long pile shaggy rug we recommend using a suction only vacuum cleaner, do not use a vacuum cleaner with a spinning brush head. Most light dirty marks can be cleaned with a damp cloth. Do not machine wash or dry clean your rug (unless the label on the back of the rug instructs that you can do so).
Stains
You should clean spills immediately. NEVER rub a spill. Blot liquids with a dry absorbent cloth or white paper towel. Some stains may be cleaned with a very mild clear detergent and lukewarm water or a good carpet shampoo. Avoid excessive moisture or wetting when cleaning the stain. Dry the rug on a flat surface. If a stain cannot be removed you should seek specialist cleaning advice. Avoid harsh chemicals as they may damage the rug. Do not machine wash or dry clean your rug (unless the label on the back of the rug instructs that you can do so).
Pile Shedding
It is completely normal for ALL wool rugs to shed some fibers, this is a natural characteristic of wool as a material. Pile shedding is also normal in some of our man-made fibre rugs (acrylic, viscose and polyester). Pile shedding is usually most noticeable in the first several months of use and can lessen over time but will not stop completely. Pile shedding does not affect the life of a rug. We recommend regular vacuuming to remove any excess fluff/fibres.
Sprouting (Long Threads) & Loose Threads
Some rugs are prone to what is known in the rug & carpet industry as sprouting or pilling. This is where some strands/threads of the pile will appear that are longer than the rest of the pile. When this occurs all you need to do it trim any longer strands with a pair of sharp scissors. It is important that you do not try to pull these long threads as this can damage the rug.
Same rule applies, If a thread becomes loose in your rug, do not pull it, but carefully cut it with sharp scissors. This will not damage the rug.
Creases or Marks in Rug Pile
You may notice that when you first unroll your new rug there are lines or creases running across the width of it. On some rugs there may only be one of these line/crease marks a few inches from one edge of the rug, whereas on some of other rugs (especially polypropylene rugs) there may be several. These line/crease marks are completely normal and are just pressure marks caused by the rug being rolled up whilst in transit. They are not permanent and will gradually fade with normal use and regular vacuuming.
Some rugs are susceptible to ‘Pile Shading’, especially rugs that have a shiny/silky pile. Pile Shading is a term in the rug & carpet industry that refers to marks caused by certain areas of the pile running in a different direction, meaning that it reflects light differently. These marks will look either a bit lighter or a bit darker than the rest of the pile in the rug. If you brush your hand over the pile of some rugs and see the colour get slightly lighter or darker. The pile of the rug needs chance to settle over a period of a few weeks so it all runs in the same direction. Frequent vacuuming or brushing of the pile can help to speed this process up.
Getting Your Rug to Lay Flat
Our rugs are stored rolled up in their plastic wrapping to ensure they stay in brand new condition. This means that they may not lay completely flat when you first unroll it. This is similar for example to when you by a new shirt or a pair of curtains which will be creased when you first take it out of the wrapping; but whereas these items can be ironed flat very quickly rugs take a little longer. This is not a fault with the rug; it is only temporary until the rug takes to its new shape being rolled out.
The more you use and walk over the rug the quicker it will flatten out. This can take anything from a few days to a few weeks depending on the type of rug you have purchased. You can sometimes speed this process up by rolling the rug in the opposite direction to the way it was rolled in its packaging (pile outwards) and leave it somewhere warm (such as near a radiator) for 24 hours.